As per the general pattern for initialisation functions in iPXE,
pci_init() saves code size by assuming that the caller has already
zeroed the underlying storage (e.g. as part of zeroing a larger
containing structure). There are several places within the code where
pci_init() is deliberately used to initialise a transient struct
pci_device without zeroing the entire structure, because the calling
code knows that only the PCI bus:dev.fn address is required to be
initialised (e.g. when reading from PCI configuration space).
Ensure that using pci_init() followed by pci_read_config() will fully
initialise the struct pci_device even if the caller did not previously
zero the underlying storage, since Coverity reports that there are
several places in the code that rely upon this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several keyboard layouts define ASCII characters as accessible only
via the AltGr modifier. Add support for this modifier to ensure that
all ASCII characters are accessible.
Experiments suggest that the BIOS console is likely to fail to
generate ASCII characters when the AltGr key is pressed. Work around
this limitation by accepting LShift+RShift (which will definitely
produce an ASCII character) as a synonym for AltGr.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Handle Ctrl and CapsLock key modifiers within key_remap(), to provide
consistent behaviour across different console types.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The key with scancode 86 appears in the position between left shift
and Z on a US keyboard, where it typically fails to exist entirely.
Most US keyboard maps define this nonexistent key as generating "\|",
with the notable exception of "loadkeys" which instead reports it as
generating "<>". Both of these mapping choices duplicate keys that
exist elsewhere in the map, which causes problems for our ASCII-based
remapping mechanism.
Work around these quirks by treating the key as generating "\|" with
the high bit set, and making it subject to remapping. Where the BIOS
generates "\|" as expected, this allows us to remap to the correct
ASCII value.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some keyboard layouts (e.g. "fr") swap letter and punctuation keys.
Apply the logic for upper and lower case and for Ctrl-<key> only after
applying remapping, in order to handle these layouts correctly.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some systems (observed with the Thunderbolt ports on a ThinkPad X1
Extreme Gen3 and a ThinkPad P53), if the IOMMU is enabled then the
system firmware will install an ExitBootServices notification event
that disables bus mastering on the Thunderbolt xHCI controller and all
PCI bridges, and destroys any extant IOMMU mappings. This leaves the
xHCI controller unable to perform any DMA operations.
As described in commit 236299b ("[xhci] Avoid DMA during shutdown if
firmware has disabled bus mastering"), any subsequent DMA operation
attempted by the xHCI controller will end up completing after the
operating system kernel has reenabled bus mastering, resulting in a
DMA operation to an area of memory that the hardware is no longer
permitted to access and, on Windows with the Driver Verifier enabled,
a STOP 0xE6 (DRIVER_VERIFIER_DMA_VIOLATION).
That commit avoids triggering any DMA attempts during the shutdown of
the xHCI controller itself. However, this is not a complete solution
since any attached and opened USB device (e.g. a USB NIC) may
asynchronously trigger DMA attempts that happen to occur after bus
mastering has been disabled but before we reset the xHCI controller.
Avoid this problem by installing our own ExitBootServices notification
event at TPL_NOTIFY, thereby causing it to be invoked before the
firmware's own ExitBootServices notification event that disables bus
mastering.
This unsurprisingly causes the shutdown hook itself to be invoked at
TPL_NOTIFY, which causes a fatal error when later code attempts to
raise the TPL to TPL_CALLBACK (which is a lower TPL). Work around
this problem by redefining the "internal" iPXE TPL to be variable, and
set this internal TPL to TPL_NOTIFY when the shutdown hook is invoked.
Avoid calling into an underlying SNP protocol instance from within our
shutdown hook at TPL_NOTIFY, since the underlying SNP driver may
attempt to raise the TPL to TPL_CALLBACK (which would cause a fatal
error). Failing to shut down the underlying SNP device is safe to do
since the underlying device must, in any case, have installed its own
ExitBootServices hook if any shutdown actions are required.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some systems (observed with the Thunderbolt ports on a ThinkPad X1
Extreme Gen3 and a ThinkPad P53), the system firmware will disable bus
mastering on the xHCI controller and all PCI bridges at the point that
ExitBootServices() is called if the IOMMU is enabled. This leaves the
xHCI controller unable to shut down cleanly since all commands will
fail with a timeout.
Commit 85eb961 ("[xhci] Allow for permanent failure of the command
mechanism") allows us to detect that this has happened and respond
cleanly. However, some unidentified hardware component (either the
xHCI controller or one of the PCI bridges) seems to manage to enqueue
the attempted DMA operation and eventually complete it after the
operating system kernel has reenabled bus mastering. This results in
a DMA operation to an area of memory that the hardware is no longer
permitted to access. On Windows with the Driver Verifier enabled,
this will result in a STOP 0xE6 (DRIVER_VERIFIER_DMA_VIOLATION).
Work around this problem by detecting when bus mastering has been
disabled, and immediately failing the device to avoid initiating any
further DMA attempts.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some xHCI controllers (observed with the Thunderbolt ports on a
ThinkPad X1 Extreme Gen3 and a ThinkPad P53) seem to suffer a
catastrophic failure at the point that ExitBootServices() is called if
the IOMMU is enabled. The symptoms appear to be consistent with
another UEFI driver (e.g. the IOMMU driver, or the Thunderbolt driver)
having torn down the DMA mappings, leaving the xHCI controller unable
to write to host memory. The observable effect is that all commands
fail with a timeout, and attempts to abort command execution similarly
fail since the xHCI controller is unable to report the abort
completion.
Check for failure to abort a command, and respond by performing a full
device reset (as recommended by the xHCI specification) and by marking
the device as permanently failed.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use the "system MAC address" provided within the DSDT/SSDT if such an
address is available and has not already been assigned to a network
device.
Tested-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RTL8211B seems to have a bug that prevents the link from coming up
unless the MII_MMD_DATA register is cleared.
The Linux kernel driver applies this workaround (in rtl8211b_resume())
only to the specific RTL8211B PHY model, along with a matching
workaround to set bit 9 of MII_MMD_DATA when suspending the PHY.
Since we have no need to ever suspend the PHY, and since writing a
zero ought to be harmless, we just clear the register unconditionally.
Debugged-by: Nikolay Pertsev <nikolay.p@cos.flag.org>
Tested-by: Nikolay Pertsev <nikolay.p@cos.flag.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hexadecimal values instead of macros in PCI_ROM entries so Perl
script can parse them correctly. Move PCI_ROM entries from header
file to C file. Integrate bnxt_vf_nics array into PCI_ROM entries by
introducing BNXT_FLAG_PCI_VF flag into driver_data field. Add
whitespaces in PCI_ROM entries for style consistency.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The use of jumbo frames for the Xen netfront virtual NIC requires the
use of scatter-gather ("feature-sg"), with the receive descriptor ring
becoming a list of page-sized buffers and the backend using as many
page buffers as required for each packet.
Since iPXE's abstraction of an I/O buffer does not include any sort of
scatter-gather list, this requires an extra allocation and copy on the
receive datapath for any packet that spans more than a single page.
This support is required in order to successfully boot an AWS EC2
virtual machine (with non-enhanced networking) via iSCSI if jumbo
frames are enabled, since the netback driver used in EC2 seems not to
allow "feature-sg" to be renegotiated once the Linux kernel driver
takes over.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no method for obtaining the number of PCI buses when using
PCIAPI_DIRECT, and we therefore currently scan all possible bus
numbers. This can cause a several-second startup delay in some
virtualised environments, since PCI configuration space access will
necessarily require the involvement of the hypervisor.
Ameliorate this situation by defaulting to scanning only a single bus,
and expanding the number of PCI buses to accommodate any subordinate
buses that are detected during enumeration.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Adding this missing identifier allows the X557-AT2 chipset seen on (at
least) Super Micro A2SDI-H-TF motherboards to function with iPXE.
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
Allow arbitrary settings to be specified on the Linux command line.
For example:
./bin-x86_64-linux/slirp.linux \
--net slirp,testserver=qa-test.ipxe.org
This can be useful when using the Linux userspace build to test
embedded scripts, since it allows arbitrary parameters to be passed
directly on the command line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a driver using libslirp to provide a virtual network interface
without requiring root permissions on the host. This simplifies the
process of running iPXE as a Linux userspace application with network
access. For example:
make bin-x86_64-linux/slirp.linux
./bin-x86_64-linux/slirp.linux --net slirp
libslirp will provide a built-in emulated DHCP server and NAT router.
Settings such as the boot filename may be controlled via command-line
options. For example:
./bin-x86_64-linux/slirp.linux \
--net slirp,filename=http://192.168.0.1/boot.ipxe
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When building as a Linux userspace application, iPXE currently
implements its own system calls to the host kernel rather than relying
on the host's C library. The output binary is statically linked and
has no external dependencies.
This matches the general philosophy of other platforms on which iPXE
runs, since there are no external libraries available on either BIOS
or UEFI bare metal. However, it would be useful for the Linux
userspace application to be able to link against host libraries such
as libslirp.
Modify the build process to perform a two-stage link: first picking
out the requested objects in the usual way from blib.a but with
relocations left present, then linking again with a helper object to
create a standard hosted application. The helper object provides the
standard main() entry point and wrappers for the Linux system calls
required by the iPXE Linux drivers and interface code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The GCC11 compiler pointed out something that apparently no previous
compiler noticed: in ath5k_eeprom_pread_turbo_modes, local variable
val is used uninitialized. From what I can see, the code is just
missing an initial AR5K_EEPROM_READ. Add it right before the switch
statement.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Linux and FreeBSD drivers for the (totally undocumented) ENA
adapters use a two-phase reset mechanism: first set ENA_CTRL.RESET and
wait for this to be reflected in ENA_STAT.RESET, then clear
ENA_CTRL.RESET and again wait for it to be reflected in
ENA_STAT.RESET.
The iPXE driver currently assumes a self-clearing reset mechanism,
which appeared to work at the time that the driver was created but
seems no longer to function, at least on the t3.nano and t3a.nano
instance types found in eu-west-1.
Switch to a simplified version of the two-phase reset mechanism as
used by Linux and FreeBSD.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
After a ton of tedious work, I am pleased to finally introduce full
support for ConnectX-3 cards in iPXE!
The work has been done by finding all publicly available versions of
the Mellanox Flexboot sources, cleaning them up, synthesizing a git
history from them, cleaning out non-significant changes, and
correlating with the iPXE upstream git history.
After this, a proof-of-concept diff was produced, that allowed iPXE to
be compiled with rudimentary ConnectX-3 support. This diff was over
10k lines, and contained many changes that were not part of the core
driver.
Special thanks to Michael Brown <mcb30@ipxe.org> for answering my
barrage of questions, and helping brainstorm the development along the
way.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
The CQE length field will not be valid for a completion in error.
Avoid parsing the length field and just call the completion handler
directly.
In debug builds, also dump the queue pair context to allow for
inspection of the error.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Check for reset completion by waiting for the device to respond to PCI
configuration cycles, as documented in the Programmer's Reference
Manual. On the original ConnectX HCA, this reduces the time spent on
reset from 1000ms down to 1ms.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When auto-detecting the initial port type, the Hermon driver will spam
the debug output without hesitation. Add a short delay in each
iteration to fix this.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Inspired by Flexboot, the function hermon_event_port_mgmnt_change() is
added to handle the HERMON_EV_PORT_MGMNT_CHANGE event type, which
updates the Infiniband subsystem.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Hermon Ethernet work queues have more RX than TX entries, unlike most
other drivers. This is possibly the source of some stochastic
deadlocks previously experienced with this driver.
Update the sizes to be in line with other drivers, and make them
slightly larger for better performance. These new queue sizes have
been found to work well with ConnectX-3 hardware.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The programming documentation states that the reset magic value is
"0x00000001 (Big Endian)", and the current code matches this by using
the value 0x01000000 for the implicitly little-endian writel().
Inspection of the FlexBoot source code reveals an exciting variety of
reset values, some suggestive of confusion around endianness.
Experimentation suggests that the value 0x01000001 works reliably
across a wide range of hardware.
Debugged-by: Christian Iversen <ci@iversenit.dk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of the hardware (and/or firmware) do not report an
event when an Infiniband link reaches the INIT state. The driver
works around this missing event by calling ib_smc_update() on each
event queue poll while the link is in the DOWN state.
Commit 6cb12ee ("[hermon] Increase polling rate for command
completions") addressed this by speeding up the time taken to issue
each command invoked by ib_smc_update(). Experimentation shows that
the impact is still significant: for example, in a situation where an
unplugged port is opened, the throughput on the other port can be
reduced by over 99%.
Fix by throttling the rate at which link polling is attempted.
Debugged-by: Christian Iversen <ci@iversenit.dk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This change is ported from Flexboot sources. When stopping a Hermon
device, perform hermon_unmap_mpt() which runs HERMON_HCR_HW2SW_MPT to
bring the Memory Protection Table (MPT) back to software control.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The eIPoIB local Ethernet MAC is currently constructed from the port
GUID. Given a base GUID/MAC value of N, Mellanox seems to populate:
Node GUID: N + 0
Port 1 GUID: N + 1
Port 2 GUID: N + 2
and
Port 1 MAC: N + 0
Port 2 MAC: N + 1
This causes a duplicate local MAC address when port 1 is configured as
Infiniband and port 2 as Ethernet, since both will derive their MAC
address as (N + 1).
Fix by using the port's Ethernet MAC as the eIPoIB local EMAC. This
is a behavioural change that could potentially break configurations
that rely on the local EMAC value, such as a DHCP server relying on
the chaddr field for DHCP reservations.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of the hardware (and/or firmware) do not report an
event when an Infiniband link reaches the INIT state. The driver
works around this missing event by calling ib_smc_update() on each
event queue poll while the link is in the DOWN state. This results in
a very large number of commands being issued while any open Infiniband
link is in the DOWN state (e.g. unplugged), to the point that the 1ms
delay from waiting for each command to complete will noticeably affect
responsiveness.
Fix by decreasing the command completion polling delay from 1ms to
10us.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add hermon_dump_eqctx() for dumping the event queue context and
hermon_dump_eqes() for dumping any unconsumed event queue entries.
Originally-implemented-by: Christian Iversen <ci@iversenit.dk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some commands (particularly in relation to device initialization) can
occasionally take longer than 2 seconds, and the Mellanox documentation
recommends a 10 second timeout.
Signed-off-by: Christian Iversen <ci@iversenit.dk>
Require drivers to report the total number of Infiniband ports. This
is necessary to report the correct number of ports on devices with
dynamic port types.
For example, dual-port Mellanox cards configured for (eth, ib) would
be rejected by the subnet manager, because they report using "port 2,
out of 1".
Signed-off-by: Christian Iversen <ci@iversenit.dk>
