The malloc_dma() function allocates memory with specified physical
alignment, and is typically (though not exclusively) used to allocate
memory for DMA.
Rename to malloc_phys() to more closely match the functionality, and
to create name space for functions that specifically allocate and map
DMA-capable buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The legacy transmit descriptor index is not reset by anything short of
a full device reset. This can cause the legacy transmit ring to stall
after closing and reopening the device, since the hardware and
software indices will be out of sync.
Fix by performing a reset after closing the interface. Do this only
if operating in legacy mode, since in C+ mode the reset is not
required and would undesirably clear additional state (such as the C+
command register itself).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A zero divisor will currently lead to a 16-bit integer overflow when
calculating the transmit padding, and a potential division by zero if
assertions are enabled.
Avoid these problems by treating a divisor value of zero as equivalent
to a divisor value of one (i.e. no alignment requirements).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently use a heuristic to determine whether or not to request
cable detection in PXE_OPCODE_INITIALIZE, based on the need to work
around a known Emulex driver bug (see commit c0b61ba "[efi] Work
around bugs in Emulex NII driver") and the need to accommodate links
that are legitimately slow to come up (see commit 6324227 "[efi] Skip
cable detection at initialisation where possible").
This heuristic appears to fail with newer Emulex drivers. Attempt to
support all known drivers (past and present) by first attempting
initialisation with cable detection, then falling back to attempting
initialisation without cable detection.
Reported-by: Kwang Woo Lee <kwleeyh@gmail.com>
Tested-by: Kwang Woo Lee <kwleeyh@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When connected to a USB3 port, the AX88179 seems to have an
approximately 50% chance of producing a USB transaction error on each
of its three endpoints after being closed and reopened. The root
cause is unclear, but rewriting the USB device configuration value
seems to clear whatever internal error state has accumulated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ASIX USB NICs are capable of autodetecting the Ethernet link speed
and reporting it via PLSR but will not automatically update the
relevant GM and PS bits in MSR. The result is that a non-gigabit link
will fail to send or receive any packets.
The interrupt endpoint used to report link state includes the values
of the PHY BMSR and LPA registers. These are not sufficient to
differentiate between 100Mbps and 1000Mbps, since the LPA_NPAGE bit
does not necessarily indicate that the link partner is advertising
1000Mbps.
Extend axge_check_link() to write the MSR value based on the link
speed read from PLSR, and simplify the interrupt endpoint handler to
merely trigger a call to axge_check_link().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GCC 10 produces a spurious warning about an out-of-bounds array access
for the unsized raw dword array in union intelvf_msg.
Avoid the warning by embedding the zero-length array within a struct.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some devices (observed with a Getac RX10 tablet and docking station
containing an embedded AX88179 USB NIC) seem to be capable of
detecting link state only during the call to Initialize(), and will
occasionally erroneously report that the link is down for the first
few such calls.
Work around these devices by retrying the Initialize() call multiple
times, terminating early if a link is detected. The eventual absence
of a link is treated as a non-fatal error, since it is entirely
possible that the link really is down.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to UEFI specification 2.8 p 24.1 we must set the
EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST bit in the "Disable" mask, when
"ResetMCastFilter" is TRUE.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Currently, if the SNP driver for whatever reason fails to enable
receive filters for multicast frames, it falls back to enabling just
unicast and broadcast filters. This breaks some IPv6 functionality as
the network card does not respond to neighbour solicitation requests.
Some cards refuse to enable EFI_SIMPLE_NETWORK_RECEIVE_MULTICAST, but
do support enabling EFI_SIMPLE_NETWORK_RECEIVE_PROMISCUOUS_MULTICAST,
so try it before falling back to just unicast+broadcast.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Split-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On devices with no EEPROM or OTP, the MAC_CR register defaults to not
using automatic link speed detection, with the result that no packets
are successfully sent or received.
Fix by always enabling automatic speed and duplex detection, since
iPXE provides no mechanism for manual configuration of either link
speed or duplex.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function defaults to operating in "PXE mode" after a
power-on reset. In this mode, receive descriptors are fetched and
written back as single descriptors. In normal (non-PXE mode)
operation, receive descriptors are fetched and written back only as
complete cachelines unless an interrupt is raised.
There is no way to return to PXE mode from non-PXE mode, and there is
no way for the virtual function driver to operate in PXE mode.
Choose to operate in non-PXE mode. This requires us to trick the
hardware into believing that it is raising an interrupt, so that it
will not defer writing back receive descriptors until a complete
cacheline (i.e. four packets) have been consumed. We do so by
configuring the hardware to use MSI-X with a dummy target location in
place of the usual APIC register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The virtual function driver will use the same transmit and receive
descriptor ring structures, but will not itself construct and program
the ring context. Split out ring creation and destruction from the
programming of the ring context, to allow code to be shared between
physical and virtual function drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The virtual function transmit and receive ring tail register offsets
do not match those of the physical function. Allow the tail register
offsets to be specified separately.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function driver does not allow the virtual function to
request the use of 16-byte receive descriptors. Switch to using
32-byte receive descriptors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a weak stub function for handling the "send to VF" event used
for communications between the physical and virtual function drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "send to PF" and "send to VF" admin queue descriptors (ab)use the
cookie field to hold the extended opcode and return code values.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A virtual function reset is triggered via an admin queue command and
will reset the admin queue configuration registers. Allow the admin
queues to be reinitialised after such a reset, without requiring the
overhead (and potential failure paths) of freeing and reallocating the
queues.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently use a single data buffer shared between all admin queue
descriptors. This works for the physical function driver since we
have at most one command in progress and only a single event (which
does not use a data buffer).
The communication path between the physical and virtual function
drivers uses the event data buffer, and there is no way to prevent a
solicited event (i.e. a response to a request) from being overwritten
by an unsolicited event (e.g. a link status change).
Provide individual data buffers for each admin event queue descriptor
(and for each admin command queue descriptor, for the sake of
consistency).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The register map for the virtual functions appears to have been
constructed using a random number generator.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The physical function driver does not allow the virtual function to
request that VLAN tags are left unstripped. Extract and use the VLAN
tag from the receive descriptor if present.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The first adapters in this family are X2522-10, X2522-25, X2541 and
X2542.
These no longer use PCI BAR 0 for I/O, but use that for memory. In
other words, BAR 2 on SFN8xxx adapters now becomes BAR 0.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Devices that support jumbo frames will currently default to the
largest possible MTU. This assumption is valid for virtual adapters
such as virtio-net, where the MTU must have been configured by a
system administrator, but is unsafe in the general case of a physical
adapter.
Default to the standard Ethernet MTU, unless explicitly overridden
either by the driver or via the ${netX/mtu} setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the function mii_find() in order to locate the PHY address.
Signed-off-by: Sylvie Barlow <sylvie.c.barlow@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently have no generic concept of a PHY address, since all
existing implementations simply hardcode the PHY address within the
MII access methods.
A bit-bashing MII interface will need to be provided with an explicit
PHY address in order to generate the correct waveform. Allow for this
by separating out the concept of a MII device (i.e. a specific PHY
address attached to a particular MII interface).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some drivers are known to call the optional Map_Mem() callback without
first checking that the callback exists. Provide a usable basic
implementation of Map_Mem() along with the other callbacks that become
mandatory if Map_Mem() is provided.
Note that in theory the PCI I/O protocol is allowed to require
multiple calls to Map(), with each call handling only a subset of the
overall mapped range. However, the reference implementation in EDK2
assumes that a single Map() will always suffice, so we can probably
make the same simplifying assumption here.
Tested with the Intel E3522X2.EFI driver (which, incidentally, fails
to cleanly remove one of its mappings).
Originally-implemented-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The i219 appears to have a seriously broken reset mechanism. After
any transmit or receive activity, resetting the card will break both
the transmit and receive datapaths until the next PCI bus reset.
The Linux and BSD drivers include a convoluted workaround authored by
Intel which involves setting a bit in the undocumented FEXTNVM11
register, then transmitting a dummy 512-byte packet containing garbage
data, then reconfiguring the receive descriptor prefetch thresholds
and temporarily reenabling the receive datapath. The comments in the
Intel fix do not even remotely match what the code actually does, and
the code accidentally leaves the transmitter enabled after use.
Experimentation suggests that an equivalent fix is to simply set the
undocumented bit in FEXTNVM11 before enabling the transmit or receive
descriptor rings.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of gcc (observed with gcc 4.7.2) report a spurious
uninitialised variable warning in ena_get_device_attributes(). Work
around this warning by manually inlining the relevant code (which has
only a single call site).
Reported-by: xbgmsharp <xbgmsharp@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most drivers do not utilise an MII interface, since the link state is
typically available directly from a memory-mapped register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
