iPXE will often have multiple drivers available for a USB device. For
example: some USB network devices will support both RNDIS and CDC-ECM,
and any device may be consumed by the fallback "usbio" driver under
UEFI in order to expose an EFI_USB_IO_PROTOCOL instance.
The driver scoring mechanism is used to select a device configuration
based on the availability of drivers for the interfaces exposed in
each configuration.
For the case of RNDIS versus CDC-ECM, this mechanism will always
produce the correct result since RNDIS and CDC-ECM will not exist
within the same configuration and so each configuration will receive a
score based on the relevant driver.
This guarantee does not hold for the "usbio" driver, which will match
against any device. It is a surprising coincidence that the "usbio"
driver seems to usually end up at the tail end of the USB drivers
list, thereby resulting in the expected behaviour.
Guarantee the expected behaviour by explicitly placing the "usbio"
driver at the end of the USB drivers list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For USB mass storage devices, we do not want to submit more bulk IN
packets than are required for the inbound data, since this will waste
memory.
Allow an upper limit to be specified on each refill attempt. The
endpoint will be refilled to the lower of this limit or the limit
specified by usb_refill_init().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Closing and reopening a USB endpoint will clear any halt status
recorded by the host controller, but may leave the endpoint halted at
the device. This will cause the first packet submitted to the
reopened endpoint to be lost, before the automatic stall recovery
mechanism detects the halt and resets the endpoint.
This is relatively harmless for USB network or HID devices, since the
wire protocols will recover gracefully from dropped packets. Some
protocols (e.g. for USB mass storage devices) assume zero packet loss
and so would be adversely affected.
Fix by allowing any device endpoint halt status to be cleared on a
freshly opened endpoint.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The length as returned by UsbGetSupportedLanguages() should not
include the length of the descriptor header itself.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow temporary debugging code to call efi_wrap_systab() to obtain a
pointer to the wrapper EFI system table. This can then be used to
e.g. forcibly overwrite the boot services table pointer used by an
already loaded and running UEFI driver, in order to trace calls made
by that driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Retrieve the address windows and translation offsets for the
appropriate PCI root bridge and use them to adjust the PCI BAR address
prior to calling ioremap().
Originally-implemented-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Define pci_ioremap() as a wrapper around ioremap() that could allow
for a non-zero address translation offset.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Older versions of gcc (observed with gcc 4.5.3) require attributes to
be specified on the first declaration of a symbol, and will silently
ignore attributes specified after the initial declaration. This
causes the ASN.1 OID-identified algorithms to end up misaligned.
Fix by adding __asn1_algorithm to the initial declarations in asn1.h.
Debugged-by: Dentcho Bankov <dbankov@vmware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
All implemented socket openers provide definitions for both IPv4 and
IPv6 using exactly the same opener method. Simplify the logic by
omitting the address family from the definition.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise the bit rotation implementations to use a common macro, and
add roll() and rorl() to handle unsigned long values.
Each function will still compile down to a single instruction.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Enable -fstack-protector for EFI builds, where binary size is less
critical than for BIOS builds.
The stack cookie must be constructed immediately on entry, which
prohibits the use of any viable entropy source. Construct a cookie by
XORing together various mildly random quantities to produce a value
that will at least not be identical on each run.
On detecting a stack corruption, attempt to call Exit() with an
appropriate error. If that fails, then lock up the machine since
there is no other safe action that can be taken.
The old conditional check for support of -fno-stack-protector is
omitted since this flag dates back to GCC 4.1.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Raw block downloads are expensive if the origin server uses HTTPS,
since each concurrent download will require local TLS resources
(including potentially large received encrypted data buffers).
Raw block downloads may also be prohibitively slow to initiate when
the origin server is using HTTPS and client certificates. Origin
servers for PeerDist downloads are likely to be running IIS, which has
a bug that breaks session resumption and requires each connection to
go through the full client certificate verification.
Limit the total number of concurrent raw block downloads to ameliorate
these problems.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Raspberry Pi NIC has no EEPROM to hold the MAC address. The
platform firmware (e.g. UEFI or U-Boot) will typically obtain the MAC
address from the VideoCore firmware and add it to the device tree,
which is then made available to subsequent programs such as iPXE or
the Linux kernel.
Add the ability to parse a flattened device tree and to extract the
MAC address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 1a7746603 ("[build] Fix use of inline assembly on GCC 4.8 ARM64
builds") switched from using "%c0" to "%a0" in order to avoid an
"invalid operand prefix" error on the ARM64 version of GCC 4.8.
It appears that the ARM64 version of GCC 8 now produces an "invalid
address mode" error for the "%a0" form, but is happy with the original
"%c0" form.
Switch back to using the "%c0" form, on the assumption that the
requirement for "%a0" was a temporary aberration.
Originally-fixed-by: John L. Jolly <jjolly@suse.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Hermon driver uses vlan_find() to identify the appropriate VLAN
device for packets that are received with the VLAN tag already
stripped out by the hardware. Generalise this capability and expose
it for use by other network card drivers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel 40 Gigabit Ethernet virtual functions support only MSI-X
interrupts, and will write back completed interrupt descriptors only
when the device attempts to raise an interrupt (or when a complete
cacheline of receive descriptors has been completed).
We cannot actually use MSI-X interrupts within iPXE, since we never
have ownership of the APIC. However, an MSI-X interrupt is
fundamentally just a DMA write of a single dword to an arbitrary
address. We can therefore configure the device to "raise" an
interrupt by writing a meaningless value to an otherwise unused memory
location: this is sufficient to trigger the receive descriptor
writeback logic.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
One of the design goals of ASN.1 DER is to provide a canonical
serialization of a data structure, thereby allowing for equality of
values to be tested by simply comparing the serialized bytes.
Some OCSP servers will modify the request certID to omit the optional
(and null) "parameters" portion of the hashAlgorithm. This is
arguably legal but breaks the ability to perform a straightforward
bitwise comparison on the entire certID field between request and
response.
Fix by comparing the OID-identified hashAlgorithm separately from the
remaining certID fields.
Originally-fixed-by: Thilo Fromm <Thilo@kinvolk.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the session ID (if any) provided by the server and attempt to
reuse it for any concurrent connections to the same server.
If multiple connections are initiated concurrently (e.g. when using
PeerDist) then defer sending the ClientHello for all but the first
connection, to allow time for the first connection to potentially
obtain a session ID (and thereby speed up the negotiation for all
remaining connections).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On a Dell OptiPlex 7010, calling DisconnectController() on the LOM
device handle will lock up the system. Debugging shows that execution
is trapped in an infinite loop that is somehow trying to reconnect
drivers (without going via ConnectController()).
The problem can be reproduced in the UEFI shell with no iPXE code
present, by using the "disconnect" command. Experimentation shows
that the only fix is to unload (rather than just disconnect) the
"Ip4ConfigDxe" driver.
Add the concept of a blacklist of UEFI drivers that will be
automatically unloaded when iPXE runs as an application, and add the
Dell Ip4ConfigDxe driver to this blacklist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the function mii_find() in order to locate the PHY address.
Signed-off-by: Sylvie Barlow <sylvie.c.barlow@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently have no generic concept of a PHY address, since all
existing implementations simply hardcode the PHY address within the
MII access methods.
A bit-bashing MII interface will need to be provided with an explicit
PHY address in order to generate the correct waveform. Allow for this
by separating out the concept of a MII device (i.e. a specific PHY
address attached to a particular MII interface).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In TLS terminology a session conceptually spans multiple individual
connections, and essentially represents the stored cryptographic state
(master secret and cipher suite) required to establish communication
without going through the certificate and key exchange handshakes.
Rename tls_session to tls_connection in order to make the name
tls_session available to represent the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently perform various min-entropy calculations using build-time
floating-point arithmetic. No floating-point code ends up in the
final binary, since the results are eventually converted to integers
and asserted to be compile-time constants.
Though this mechanism is undoubtedly cute, it inhibits us from using
"-mno-sse" to prevent the use of SSE registers by the compiler.
Fix by using fixed-point arithmetic instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the ACPI power management timer to be used if enabled via
TIMER_ACPI in config/timer.h. This provides an alternative timer on
systems where the standard 8254 PIT is unavailable or unreliable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some CAs provide non-functional OCSP servers, and some clients are
forced to operate on networks without access to the OCSP servers.
Allow the user to explicitly disable the use of OCSP checks by
undefining OCSP_CHECK in config/crypto.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Mark the link as blocked if the LACP partner is not reporting itself
as being in sync, collecting, and distributing.
This matches the behaviour for STP: we mark the link as blocked if we
detect that the switch is actively blocking traffic, in order to
extend the DHCP discovery period and so prevent boot failures on
switches that take an excessively long time to enable ports.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow individual authentication schemes to parse WWW-Authenticate
headers that do not comply with RFC2617.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
