[axge] Add driver for ASIX 10/100/1000 USB Ethernet NICs

Add driver for the AX88178A (USB2) and AX88179 (USB3) 10/100/1000
Ethernet NICs.

Signed-off-by: Michael Brown <mcb30@ipxe.org>

src/drivers/net/axge.h

@@ -0,0 +1,174 @@
+#ifndef _AXGE_H
+#define _AXGE_H
+
+/** @file
+ *
+ * Asix 10/100/1000 USB Ethernet driver
+ *
+ */
+
+FILE_LICENCE ( GPL2_OR_LATER_OR_UBDL );
+
+#include <ipxe/usb.h>
+#include <ipxe/usbnet.h>
+
+/** Read MAC register */
+#define AXGE_READ_MAC_REGISTER						\
+	( USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE |		\
+	  USB_REQUEST_TYPE ( 0x01 ) )
+
+/** Write MAC register */
+#define AXGE_WRITE_MAC_REGISTER						\
+	( USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE |		\
+	  USB_REQUEST_TYPE ( 0x01 ) )
+
+/** Physical Link Status Register */
+#define AXGE_PLSR 0x02
+#define AXGE_PLSR_EPHY_10		0x10	/**< Ethernet at 10Mbps */
+#define AXGE_PLSR_EPHY_100		0x20	/**< Ethernet at 100Mbps */
+#define AXGE_PLSR_EPHY_1000		0x40	/**< Ethernet at 1000Mbps */
+#define AXGE_PLSR_EPHY_ANY						\
+	( AXGE_PLSR_EPHY_10 |						\
+	  AXGE_PLSR_EPHY_100 |						\
+	  AXGE_PLSR_EPHY_1000 )
+
+/** RX Control Register */
+#define AXGE_RCR 0x0b
+#define AXGE_RCR_PRO			0x0001	/**< Promiscuous mode */
+#define AXGE_RCR_AMALL			0x0002	/**< Accept all multicasts */
+#define AXGE_RCR_AB			0x0008	/**< Accept broadcasts */
+#define AXGE_RCR_SO			0x0080	/**< Start operation */
+
+/** Node ID Register */
+#define AXGE_NIDR 0x10
+
+/** Medium Status Register */
+#define AXGE_MSR 0x22
+#define AXGE_MSR_GM			0x0001	/**< Gigabit mode */
+#define AXGE_MSR_FD			0x0002	/**< Full duplex */
+#define AXGE_MSR_RFC			0x0010	/**< RX flow control enable */
+#define AXGE_MSR_TFC			0x0020	/**< TX flow control enable */
+#define AXGE_MSR_RE			0x0100	/**< Receive enable */
+
+/** Ethernet PHY Power and Reset Control Register */
+#define AXGE_EPPRCR 0x26
+#define AXGE_EPPRCR_IPRL		0x0020	/**< Undocumented */
+
+/** Delay after initialising EPPRCR */
+#define AXGE_EPPRCR_DELAY_MS 200
+
+/** Bulk IN Control Register (undocumented) */
+#define AXGE_BICR 0x2e
+
+/** Bulk IN Control (undocumented) */
+struct axge_bulk_in_control {
+	/** Control */
+	uint8_t ctrl;
+	/** Timer */
+	uint16_t timer;
+	/** Size */
+	uint8_t size;
+	/** Inter-frame gap */
+	uint8_t ifg;
+} __attribute__ (( packed ));
+
+/** Clock Select Register (undocumented) */
+#define AXGE_CSR 0x33
+#define AXGE_CSR_BCS			0x01	/**< Undocumented */
+#define AXGE_CSR_ACS			0x02	/**< Undocumented */
+
+/** Delay after initialising CSR */
+#define AXGE_CSR_DELAY_MS 100
+
+/** Transmit packet header */
+struct axge_tx_header {
+	/** Packet length */
+	uint32_t len;
+	/** Answers on a postcard, please */
+	uint32_t wtf;
+} __attribute__ (( packed ));
+
+/** Receive packet footer */
+struct axge_rx_footer {
+	/** Packet count */
+	uint16_t count;
+	/** Header offset */
+	uint16_t offset;
+} __attribute__ (( packed ));
+
+/** Receive packet descriptor */
+struct axge_rx_descriptor {
+	/** Checksum information */
+	uint16_t check;
+	/** Length and error flags */
+	uint16_t len_flags;
+} __attribute__ (( packed ));
+
+/** Receive packet length mask */
+#define AXGE_RX_LEN_MASK 0x1fff
+
+/** Receive packet length alignment */
+#define AXGE_RX_LEN_PAD_ALIGN 8
+
+/** Receive packet CRC error */
+#define AXGE_RX_CRC_ERROR 0x2000
+
+/** Receive packet dropped error */
+#define AXGE_RX_DROP_ERROR 0x8000
+
+/** Interrupt data */
+struct axge_interrupt {
+	/** Magic signature */
+	uint16_t magic;
+	/** Link state */
+	uint16_t link;
+	/** PHY register MR01 */
+	uint16_t mr01;
+	/** PHY register MR05 */
+	uint16_t mr05;
+} __attribute__ (( packed ));
+
+/** Interrupt magic signature */
+#define AXGE_INTR_MAGIC 0x00a1
+
+/** Link is up */
+#define AXGE_INTR_LINK_PPLS 0x0001
+
+/** An AXGE network device */
+struct axge_device {
+	/** USB device */
+	struct usb_device *usb;
+	/** USB bus */
+	struct usb_bus *bus;
+	/** Network device */
+	struct net_device *netdev;
+	/** USB network device */
+	struct usbnet_device usbnet;
+};
+
+/** Interrupt maximum fill level
+ *
+ * This is a policy decision.
+ */
+#define AXGE_INTR_MAX_FILL 2
+
+/** Bulk IN maximum fill level
+ *
+ * This is a policy decision.
+ */
+#define AXGE_IN_MAX_FILL 8
+
+/** Bulk IN buffer size
+ *
+ * This is a policy decision.
+ */
+#define AXGE_IN_MTU 2048
+
+/** Amount of space to reserve at start of bulk IN buffers
+ *
+ * This is required to allow for protocols such as ARP which may reuse
+ * a received I/O buffer for transmission.
+ */
+#define AXGE_IN_RESERVE sizeof ( struct axge_tx_header )
+
+#endif /* _AXGE_H */